A cold shower is an unwelcome surprise any time of year, but it feels especially urgent during a Minnesota winter. Knowing how to relight water heater pilot lights can help in one specific situation: a conventional gas storage-tank water heater with a standing pilot that has gone out. The key is knowing when a careful reset is reasonable and when the safest choice is to stop and call a professional.

Not every water heater has a pilot light you can relight. Many newer gas units use electronic ignition, while electric and heat pump water heaters do not use gas or a pilot at all. Before touching the controls, make sure you know which type of system you have.

Start With Safety, Not the Igniter

A gas water heater should never be relit if you smell natural gas near the appliance or elsewhere in the home. Natural gas may smell like rotten eggs or sulfur because of an added odorant. If you notice that smell, do not use a lighter, flip electrical switches, operate the water heater, or start a vehicle in an attached garage.

Leave the home, call the gas utility or 911 from a safe location, and follow their instructions. A pilot light that will not stay lit can sometimes point to a gas supply, venting, or equipment problem. It is not worth taking chances with combustion safety.

You should also stop and arrange service if you see soot around the water heater, water leaking from the tank, corrosion on the gas line, a damaged vent pipe, or a yellow, wavering pilot flame. A healthy pilot flame is generally small and blue. Some systems may show a slight yellow tip, but a mostly yellow flame needs professional attention.

Confirm That Your Water Heater Has a Standing Pilot

Look at the control valve on the lower front of the tank. A conventional standing-pilot water heater typically has a temperature dial and a gas control knob marked ON, OFF, and PILOT. It may have a separate red or black igniter button nearby.

If the unit has a digital display, a power cord, diagnostic lights, or instructions that refer to electronic ignition, do not assume the steps below apply. Follow the manufacturer instructions on the unit or call a qualified technician. Trying to manually light a system designed for automatic ignition can damage equipment or create a safety concern.

Before proceeding, locate the printed lighting instructions. They are often on a large label attached to the water heater. Those instructions take priority because button locations and timing vary by manufacturer and model.

How to Relight a Water Heater Pilot Light

Once you have confirmed there is no gas odor and you have a conventional gas water heater, use the manufacturer label as your guide. In most cases, the process follows these steps.

First, turn the gas control knob to OFF. If the knob will not turn easily, do not force it. Wait at least five full minutes before doing anything else. This pause allows any unburned gas near the burner chamber to dissipate.

After five minutes, check again for the smell of gas. If you smell gas, stop immediately, leave the area, and contact the gas utility or emergency services from outside. If there is no gas odor, turn the control knob to PILOT.

Next, press and hold the pilot control or control knob, depending on the design. While continuing to hold it down, press the igniter button repeatedly. You may hear a clicking sound as it creates a spark. Many water heaters have a small viewing window near the bottom where you can look for the pilot flame.

Keep holding the pilot control for the amount of time listed on the water heater label, often 30 to 60 seconds after the pilot lights. This gives the thermocouple or flame sensor time to warm up and confirm there is a flame. Release the control slowly. If the pilot remains lit, turn the knob back to ON and set the temperature to your normal setting.

Avoid setting the thermostat higher than necessary. For many households, 120 degrees Fahrenheit provides a good balance of comfort, energy use, and scald protection. Homes with young children, older adults, or anyone sensitive to hot water may benefit from extra caution with temperature settings.

Finally, replace any access panel you removed and give the water heater time to recover. A tank water heater may need 30 to 60 minutes to heat a full tank, depending on its size, incoming water temperature, and how much hot water was recently used.

If the Pilot Will Not Light or Stay Lit

Do not keep trying indefinitely. Two or three careful attempts are enough. Repeatedly pressing the igniter without success can allow gas to build up, and the underlying issue will not correct itself.

A pilot that will not light may be caused by an empty or interrupted gas supply, a closed gas shutoff valve, a failed igniter, or a dirty pilot assembly. If the pilot lights but goes out as soon as you release the control, the thermocouple, flame sensor, or gas control valve may be failing. These are service issues, not good do-it-yourself repairs for most homeowners.

Start with the simple checks. Make sure the gas control is set correctly, the gas shutoff valve is open, and other gas appliances in the home are working normally. The handle on a typical quarter-turn gas valve should be parallel with the pipe when it is open. If you are not sure what you are looking at, leave it alone and call for help.

A water heater may also shut down because of venting or combustion-air problems. Snow, ice, animal nests, and debris can affect exterior vent terminations on certain high-efficiency or power-vent models. Never block vents or attempt to modify vent piping. In the Twin Cities, snow accumulation around exterior equipment is a practical concern, but clearing should be done carefully and only when it is safe to do so.

Why a Pilot Light Goes Out

One pilot outage does not always mean the water heater is failing. A temporary interruption in gas service, a strong draft, or a minor ignition issue can put out a standing pilot. Still, a pilot that repeatedly goes out is a warning sign worth addressing.

Common causes include a worn thermocouple, a dirty pilot orifice, insufficient combustion air, a failing gas valve, or a venting issue. Older water heaters may also have multiple age-related concerns at once. If the tank is nearing the end of its expected service life, putting money into repeated repairs may not be the best long-term choice.

Watch for other clues that replacement could be closer than you think: rusty water, rumbling or popping noises, moisture around the tank base, inconsistent water temperature, or a unit that is more than 10 to 12 years old. Repair may still make sense, but a professional assessment gives you a clearer picture of the cost and safety trade-offs.

When to Call for Water Heater Service

Call for professional help if the pilot will not stay lit, the water heater has no visible lighting instructions, you smell gas, or the unit shows signs of damage or poor combustion. It is also wise to call when there is no hot water but the pilot appears to be on. The problem may involve the burner, thermostat, dip tube, heating elements on an electric model, or another component that needs diagnosis.

At Four Seasons Air Specialists, our experienced technicians help homeowners in White Bear Lake and the greater northeast Twin Cities identify the cause of water heater problems and explain the practical options. Whether the fix is a repair, maintenance issue, or replacement decision, the goal is dependable hot water and safe operation in your home.

If your pilot relights and stays on, keep an eye on the system over the next day or two. If it goes out again, treat that as a reason to schedule service rather than another routine reset. Reliable hot water should not depend on repeated trial and error.